Articles of the Computational Engineering and Physical Modeling (2018-2025): RIS Format
2025
Norouzi, Y., Ghasemi, S. H., Jalayer, M. Probabilistic Infrastructure Failure Cost Analysis Integrating with Equity Cost Using the Reliability Analysis. Computational Engineering and Physical Modeling, 2025; 8(2): 19-45. https://doi.org/10.22115/cepm.2025.515772.1367
Kowsari, N., Hassanpour Golriz, M., Rezaie, Z., Jafari, M. Nazem, Ghalehnovi, M. Tilt-Up System Optimization for Lattice Towers. Computational Engineering and Physical Modeling, 2025; 8(2): 1-18. https://doi.org/10.22115/cepm.2025.497653.1359
Rezaeemanesh, M., Alibazi, A. Performance Evaluation of Earthquake Acceleration Attenuation Models (1994–2023): A Case Study of the December 5, 2024 Khuzestan Earthquake. Computational Engineering and Physical Modeling, 2025; 8(1): 83-107. https://doi.org/10.22115/cepm.2025.495690.1356
Ismail, R. Ismail, Al-Tarafany, D. M., Risan, H. K. Geometric Optimization of Indeterminate Truss Structures under Non-Loading Effects. Computational Engineering and Physical Modeling, 2025; 8(1): 71-82. https://doi.org/10.22115/cepm.2025.490480.1348
Magugu, K., Ekolu, S., Naghizadeh, A., Quainoo, H. Mixture - Related Factors Influencing Setting for Ambient Curing of Fly Ash – Based Geopolymer Binders. Computational Engineering and Physical Modeling, 2025; 8(1): 50-70. https://doi.org/10.22115/cepm.2025.490076.1347
Al-Doori, S., Abbassi, B., Ramahi, O. A Comparative Life Cycle Assessment (LCA) of Monopole Antenna and Microwave Oven for Water Heating. Computational Engineering and Physical Modeling, 2025; 8(1): 36-49. https://doi.org/10.22115/cepm.2024.488924.1344
Pan, S., Lee, B., Wu, Y. Automated System Using HMM for Lung Disease Recognition Based on Cough Sounds. Computational Engineering and Physical Modeling, 2025; 8(1): 25-35. https://doi.org/10.22115/cepm.2024.490612.1350
Bakhshi, H., Rahimi, M. Jawad, Rastin, M. Najim, Rezaie, Z. Seismic Hazard Evaluation and Accelerated Curves for Kunduz City (Afghanistan). Computational Engineering and Physical Modeling, 2025; 8(1): 1-24. https://doi.org/10.22115/cepm.2024.490533.1349
2024
Tayisepi, N., Mugwagwa, L., Mnkandla, A. Nkulumo, Mapindu, I., Muhla, T. McDonald Experimental Investigation and Simultaneous Optimisation of Honing Parameters of Dry Cast Iron Cylinder Relining Sleeves of Motor Vehicle Engine Blocks for Surface Finish and Energy Use. Computational Engineering and Physical Modeling, 2024; 7(4): 88-103. https://doi.org/10.22115/cepm.2024.473138.1324
Mia, M. Rezars, Hosen, K., Chakma, K. Compressive and Tensile Strength Increment of Concrete Using Recycled Aggregates and Rice Husk Ash. Computational Engineering and Physical Modeling, 2024; 7(4): 76-87. https://doi.org/10.22115/cepm.2024.465509.1318
Moradi, F., Sabouri, J., Sayyedfattahi, S. Determining Vibration Frequency and Damping of Metal Beams Using Image Processing Method. Computational Engineering and Physical Modeling, 2024; 7(4): 63-75. https://doi.org/10.22115/cepm.2024.477807.1332
Sahu, P., Londhe, S. N., Kulkarni, P. S. Knowledge Extraction from Trained ANN River Water Quality Parameters. Computational Engineering and Physical Modeling, 2024; 7(4): 45-62. https://doi.org/10.22115/cepm.2024.459617.1312
Parmo, P., Wardhana, I. Investigating the Influence of Cement and Additive Normalization on Concrete Compressive Strength: A Statistical Analysis. Computational Engineering and Physical Modeling, 2024; 7(4): 22-44. https://doi.org/10.22115/cepm.2024.484143.1335
Ghazvinian, H., Karami, H. Investigating the Effect of Climatic Parameters Predicting the Mortality Rate Due to Cardiovascular and Respiratory Disease with Soft Computing Methods. Computational Engineering and Physical Modeling, 2024; 7(4): 1-21. https://doi.org/10.22115/cepm.2024.475971.1328
Falowo, O. Olusola, Oluwasegunfunmi, V., Babatunde, A. Oluwatobi, Kunle, O. Williams Ground Penetrating Radar for Monitoring Damage in Reinforced Concrete Bridges: A Reliable Tool for Structural Health Assessment. Computational Engineering and Physical Modeling, 2024; 7(3): 108-123. https://doi.org/10.22115/cepm.2024.488656.1343
Jueyendah, S., Martins, C. H. Optimal Design of Welded Structure Using SVM. Computational Engineering and Physical Modeling, 2024; 7(3): 84-107. https://doi.org/10.22115/cepm.2024.485191.1338
Dumka, P., Chauhan, R., Srivastava, A. Kumar Modelling of Gust Factor Based Dynamic Loading of Buildings Using Python Programming. Computational Engineering and Physical Modeling, 2024; 7(3): 61-83. https://doi.org/10.22115/cepm.2024.481867.1333
Ahmed, B., Palash, A. G. R. Analysis and Design of High-Rise Reinforced Concrete Structures under Torsional Action. Computational Engineering and Physical Modeling, 2024; 7(3): 45-60. https://doi.org/10.22115/cepm.2024.461751.1319
Londhe, S., Kulkarni, P., Dixit, P., Shah, S., Joshi, S., Sahu, P. S. Unveiling the Artificial Neural Network Mystery with Special Reference to Applications in Civil Engineering. Computational Engineering and Physical Modeling, 2024; 7(3): 18-44. https://doi.org/10.22115/cepm.2024.461759.1315
Hosen, K. Optimal Shear Wall Placement for Seismic Performance: A Comparative Study of Building Codes. Computational Engineering and Physical Modeling, 2024; 7(3): 1-17. https://doi.org/10.22115/cepm.2024.460789.1313
Nwaiwu, C. Malachy, Mbamalu, F. Chibueze, Ubani, O. Uzodimma Modeling of the Geotechnical Properties of Soils Improved with Quarry Dust at Different Compaction Energies. Computational Engineering and Physical Modeling, 2024; 7(2): 86-112. https://doi.org/10.22115/cepm.2024.456982.1309
Deulkar, A. Mahadeorao, Jain, R. K., Londhe, S. N., Dixit, P. R. Rainfall- Runoff Modelling using HEC-HMS and ANN for Shiavde, Upper Krishna Basin, India. Computational Engineering and Physical Modeling, 2024; 7(2): 68-85. https://doi.org/10.22115/cepm.2024.458023.1310
Bakhshi, H., Kooshkaki, A., Dolatabadi, M. H., Rezaie, Z., Fakharian, P. The Efficiency of Membrane Curing Method in Hydration Temperature, Compressive Strength, and Curing Cost of Concrete. Computational Engineering and Physical Modeling, 2024; 7(2): 49-67. https://doi.org/10.22115/cepm.2024.453292.1302
Hosen, K. Assessment and Rehabilitation of Seismically Vulnerable Industrial RCC Structures. Computational Engineering and Physical Modeling, 2024; 7(2): 30-48. https://doi.org/10.22115/cepm.2024.455226.1306
Abdi Moghadam, M., Abbasi Oshaghi, A., fazlavi, M. A Comprehensive Review of The Effect of Various PET Fiber Percentages and Shapes on The Mechanical Properties of Concrete. Computational Engineering and Physical Modeling, 2024; 7(2): 15-29. https://doi.org/10.22115/cepm.2024.455265.1307
Mohanraj, R., Senthilkumar, S., Amutham, B., Krishnasamy, R. Concrete Strength: Rubber Crumbs and Steel Slag Mix - Python Analysis. Computational Engineering and Physical Modeling, 2024; 7(2): 1-14. https://doi.org/10.22115/cepm.2024.450919.1296
Dumbre, S. Uday, Dixit, P. Rajendra, Londhe, S. Performance Evaluation of CMIP6-GCMs Using Three Spatial Interpolation Methods Over Catchment Area of Koyna Reservoir, India. Computational Engineering and Physical Modeling, 2024; 7(1): 103-121. https://doi.org/10.22115/cepm.2024.453886.1304
Yosefi, A., Nasseri, H. A Review Investigation of Damage Identification in Structures via Internet of Things. Computational Engineering and Physical Modeling, 2024; 7(1): 83-102. https://doi.org/10.22115/cepm.2024.450000.1295
Almasi, S. Z., Almasi, S. A., Goli Khorasgani, A., Se, C., Goniewicz, K., Bitaraf, S., Ratanavaraha, V., Bahmani, H., A. Dulebenets, M. Decoding the Factors behind Rising Fatal Roadway Crashes in Iran: an In-Depth Analysis and Predictive Modelling Study. Computational Engineering and Physical Modeling, 2024; 7(1): 59-82. https://doi.org/10.22115/cepm.2024.452006.1299
Amirabadi, H. Dynamics of a Sandwich Cylindrical Shell with a Functionally Graded Auxetic Honeycomb Core. Computational Engineering and Physical Modeling, 2024; 7(1): 33-58. https://doi.org/10.22115/cepm.2024.442780.1283
Ohwofadjeke, P. Ogheneochuko, Udo, A. Effiong, Jonah, J. Okon Characterization of Fluid-Structure Interaction on Hydrodynamic Performance of Different Ship Hulls Using ANSYS. Computational Engineering and Physical Modeling, 2024; 7(1): 12-32. https://doi.org/10.22115/cepm.2024.431514.1269
Kamran, H., Komasi, M., Beiranvand, B. Optimizing the Design of Nickel and Composite Pressure Vessels. Computational Engineering and Physical Modeling, 2024; 7(1): 1-11. https://doi.org/10.22115/cepm.2024.434708.1278
2023
Sarsam, S. Issa Influence of Additives on the Failure Mode of Asphalt Concrete. Computational Engineering and Physical Modeling, 2023; 6(4): 77-87. https://doi.org/10.22115/cepm.2024.449235.1289
Mahdavi, M., Babaafjaei, A., Hosseini, S. R. Evaluation and Comparison of Seismic Performance in Irregular Steel Structures with Modern Concentrically Braces. Computational Engineering and Physical Modeling, 2023; 6(4): 57-76. https://doi.org/10.22115/cepm.2024.434360.1277
Hong, C. Thermal Vibration of Thick Functionally Graded Material Spherical Shells by Using Third-order Shear Deformation Theory and Simply Homogeneous Equation. Computational Engineering and Physical Modeling, 2023; 6(4): 44-56. https://doi.org/10.22115/cepm.2024.449661.1293
Behbahani, F., Hamzei, M., Mehrdoost, Z., Moghiman, M. Numerical Investigation of Car Park Fire at Special Weather Conditions. Computational Engineering and Physical Modeling, 2023; 6(4): 32-43. https://doi.org/10.22115/cepm.2024.433423.1275
Nwafor, E. Okechukwu, Duru, C. Ndubuisi, Horsfall, B. Economic Importance of Solid Waste in the Production of Pyrolytic Oil Utilized in Polymer Modified Bio-Binder Production in Makurdi Nigeria. Computational Engineering and Physical Modeling, 2023; 6(4): 21-31. https://doi.org/10.22115/cepm.2024.433298.1274
Faria, A. Wilian, Venâncio, S. de Sousa, Siqueira, A. Francisco, Romão, E. Claro Numerical Study of Hydraulic Percolation in Porous Media Using Two Hydraulic Structures. Computational Engineering and Physical Modeling, 2023; 6(4): 1-20. https://doi.org/10.22115/cepm.2024.430486.1266
Ida blessy, S., Arunprasath, K., Kasiviswanathan, M. Mechanical Properties of Partial Replacement of Cement by adding Neem Gum/Accaacia Gum a Naturally Available Polymeric Fillers. Computational Engineering and Physical Modeling, 2023; 6(3): 72-83. https://doi.org/10.22115/cepm.2024.434125.1276
Vashpanov, Y. Alex, Kudelya, A. Mikhail, Podousova, T. Underground 3D Topography Measured by Radar Sounding. Computational Engineering and Physical Modeling, 2023; 6(3): 61-71. https://doi.org/10.22115/cepm.2024.432336.1273
Fridhi, A., Laribi, R., Bali, N. N. 3D Modeling and Augmented Reality for Learning. Computational Engineering and Physical Modeling, 2023; 6(3): 52-60. https://doi.org/10.22115/cepm.2024.427616.1260
Kamran, H., Komasi, M., Beiranvand, B. Numerical Analysis of the Effect of Blast Wave on Pressure Vessels. Computational Engineering and Physical Modeling, 2023; 6(3): 39-51. https://doi.org/10.22115/cepm.2023.431112.1268
Ogolo, N. Amoni, Ukwu, A., Okoroafor, I., Onyekonwu, M. O. Viscosity Model of Polymer Extract from Irvingia Gabonensis. Computational Engineering and Physical Modeling, 2023; 6(3): 27-38. https://doi.org/10.22115/cepm.2024.431704.1270
Mohasel, M. Hosein, Mostafa Gharabaghi, A. R., Chenaghlou, M. R. Presenting an Optimal Design Procedure for a Variety of TLCDs to Improve the Seismic Response of Offshore Platforms. Computational Engineering and Physical Modeling, 2023; 6(3): 1-26. https://doi.org/10.22115/cepm.2024.428789.1265
Benmansour, N. Effective Thermal Conductivity of Composites: Numerical Study. Computational Engineering and Physical Modeling, 2023; 6(2): 90-99. https://doi.org/10.22115/cepm.2023.423376.1251
Mahdavi, M., Hosseini, S., Babaafjaei, A. Modelling and Comparison of Plastic Performance in Ten Types of New Steel Braces under Pushover Analysis. Computational Engineering and Physical Modeling, 2023; 6(2): 73-89. https://doi.org/10.22115/cepm.2023.428826.1262
Wani, K. U. Faisal, Nallasivam, K. Analysis of Rigid Pavement Subjected to Aircraft Load Using Finite Element Technique. Computational Engineering and Physical Modeling, 2023; 6(2): 51-72. https://doi.org/10.22115/cepm.2024.418199.1248
Kolo, D. Ndakuta, Kolo, S. Sunday, Hadi, A. Moh Reliability Assessment of Natural Aggregate- Pulverized Glass Powder Concrete Beam Subjected to Shearing Forces. Computational Engineering and Physical Modeling, 2023; 6(2): 43-50. https://doi.org/10.22115/cepm.2023.418933.1249
Foroudi, A., Barati, R. Discharge Coefficient Estimation of Sharp-Crested Curved-Plan Spillways using Soft Computing Approaches. Computational Engineering and Physical Modeling, 2023; 6(2): 23-42. https://doi.org/10.22115/cepm.2023.428925.1263
Sinaga, L., Husin, A. Eddy, Kristiyanto, K., Arif, E. Juni, Pinem, M. Permana Blockchain-Building Information Modeling (BIM): Aplication in Cost Eficiency of Retrofitting Green Chemical Industrial Buildings. Computational Engineering and Physical Modeling, 2023; 6(2): 1-22. https://doi.org/10.22115/cepm.2023.426269.1257
Adegun, I. Kayode, Muhammed, K. Olalekan, Anyaegbuna, B. E. Numerical Modelling of Mixability of Highly Viscous Syrup in a U-Shaped Tank with Centrally Rotated Streamers. Computational Engineering and Physical Modeling, 2023; 6(1): 70-84. https://doi.org/10.22115/cepm.2023.425761.1252
Rababah, M., Maydanchi, M., Pouya, S., Basiri, M., Norouzi Azad, A., Haji, F., Amin Jarrahi, M. Data Visualization of Traffic Violations in Maryland, U.S.. Computational Engineering and Physical Modeling, 2023; 6(1): 57-69. https://doi.org/10.22115/cepm.2023.410985.1243
Mane, K. M., Chavan, S. P., Salokhe, S. A., Nadgouda, P. A., Kumbhar, Y. D. An ANN to Predict Sorptivity and Water Absorption of Concrete Made with Industrial Waste and Artificial Sand. Computational Engineering and Physical Modeling, 2023; 6(1): 44-56. https://doi.org/10.22115/cepm.2023.402893.1239
Ribeiro, V. G., Zabadal, J. G., Staudt, E., Marinho, J. A., Silveira, A. M., Silveira, S. R. Analytical Simulations for Spill Point Source Localization Using Inverse Problems in Closed Form. Computational Engineering and Physical Modeling, 2023; 6(1): 36-43. https://doi.org/10.22115/cepm.2023.417005.1247
Narendra Kumar, B., Akhil Kumar, A., Rushikesh, M. Assessment of Crack Development Age Due to Corrosion on Reinforced High Strength Self Compacting Concrete with Inclusion of Potential Ternary Blended Cementitious Materials. Computational Engineering and Physical Modeling, 2023; 6(1): 18-35. https://doi.org/10.22115/cepm.2023.399054.1238
Khadem, S., Asif, T. Hossain, Islam, S., Rashid, M. Ur., Roy, S. Numerical Analysis of Slope Stability with Nailing Method Using Bamboo as Nailing Material. Computational Engineering and Physical Modeling, 2023; 6(1): 1-17. https://doi.org/10.22115/cepm.2023.407999.1241
Houari, O. Probabilistic Analysis of Bearing Capacity with the Pressuremeter Method. Computational Engineering and Physical Modeling, 2022; 5(4): 102-112. https://doi.org/10.22115/cepm.2023.353822.1218
Bharti, S., Nallasivam, K., Wani, K. U. Static Analysis of Rigid Pavement Runway under the Influence of Aircraft Loading by Finite Element Technique. Computational Engineering and Physical Modeling, 2022; 5(4): 79-101. https://doi.org/10.22115/cepm.2023.394133.1236
Ogolo, N., Achor, T., Onyekonwu, M. Effect of Aluminum Oxide Powder and Nanoparticles on Kaolinite Mobilization in Sand. Computational Engineering and Physical Modeling, 2022; 5(4): 67-78. https://doi.org/10.22115/cepm.2023.381797.1229
Karamizadeh, E., Sharifi, Y., Javaheri-Tafti, M. R. An Innovative Forecasting Formula for Axial Compression Capacity of Circular Steel Tubes Filled with Concrete through Neural Networks. Computational Engineering and Physical Modeling, 2022; 5(4): 51-66. https://doi.org/10.22115/cepm.2023.394004.1235
Mathi, K., Nallasivam, K. Static Analysis of Rigid Airfield Pavement Using Finite Element Method Vs Closed-Form Solution. Computational Engineering and Physical Modeling, 2022; 5(4): 23-50. https://doi.org/10.22115/cepm.2023.354941.1219
Babaei, A., Parker, J., Moshaver, P. Adaptive Neuro-Fuzzy Inference System (ANFIS) Integrated with Genetic Algorithm to Optimize Piezoelectric Cantilever-Oscillator-Spring Energy Harvester: Verification with Closed-Form Solution. Computational Engineering and Physical Modeling, 2022; 5(4): 1-22. https://doi.org/10.22115/cepm.2023.375302.1227
Islam, T., Yasar, R., Chowdhury, S. Numerical Analysis of Retrofitted RC Column under Lateral Load. Computational Engineering and Physical Modeling, 2022; 5(3): 82-95. https://doi.org/10.22115/cepm.2023.374244.1226
Gebremedhin, G. A., Gebregziabher, H. F. Finite Element Based Investigation of Belled Piers in Expansive Soils. Computational Engineering and Physical Modeling, 2022; 5(3): 64-81. https://doi.org/10.22115/cepm.2023.364210.1223
Paswan, A., Kapri, P., Singh, I., Raj, R., Anbukumar, S., Meena, R. Study of Traffic Forecast for Intelligent Transportation System. Computational Engineering and Physical Modeling, 2022; 5(3): 50-63. https://doi.org/10.22115/cepm.2023.360823.1221
Motamed, S., Askari, E., Farhoudi, Z. Facial Emotion Recognition Using Convolutional Brain Emotional Learning (CBEL) Model. Computational Engineering and Physical Modeling, 2022; 5(3): 38-49. https://doi.org/10.22115/cepm.2023.368199.1224
Incharashree, K., Prajwal, R., Kiran, K., Prasad, C. Analytical Study of Fatigue Crack Growth Behavior of Steel Structure Reinforced with FRP. Computational Engineering and Physical Modeling, 2022; 5(3): 24-37. https://doi.org/10.22115/cepm.2022.351723.1216
Mathi, K. K., Nallasivam, K. Dynamic and Fatigue Life Prediction Analysis of Airfield Runway Rigid Pavement Using Finite Element Method. Computational Engineering and Physical Modeling, 2022; 5(3): 1-23. https://doi.org/10.22115/cepm.2022.347999.1215
Palash, A. G. R. Study of the Effect of Vibration Characteristics on the Stability of RC Structures. Computational Engineering and Physical Modeling, 2022; 5(2): 113-129. https://doi.org/10.22115/cepm.2022.319200.1195
Kumar, B., Kumar, P. Effect on the Addition of Nano Silica Particles and Peg on the Rheological, Strength and Durability Properties of High Strength Self Curing Self Compacting Concrete. Computational Engineering and Physical Modeling, 2022; 5(2): 91-112. https://doi.org/10.22115/cepm.2022.345987.1213
Anirood, K., Rugbani, A. Aerodynamic Analysis of Autonomous Battery Electric Truck Concepts for Drag Reduction. Computational Engineering and Physical Modeling, 2022; 5(2): 71-90. https://doi.org/10.22115/cepm.2022.352845.1217
Hasan, M., Islam, S., Ali, A., Rezuan, M., Debnath, T. Numerical Assessment of Isolated Footing Capacity due to its Size and the Impact of Neighboring Foundation. Computational Engineering and Physical Modeling, 2022; 5(2): 45-70. https://doi.org/10.22115/cepm.2022.320189.1196
Gupta, V., Reddy, G., Pendhari, S. Response Control of Structures Subjected to Multi-Hazards of Earthquake and Wind Using Base Isolators and Absorbers. Computational Engineering and Physical Modeling, 2022; 5(2): 19-44. https://doi.org/10.22115/cepm.2022.317125.1192
Salehi Fereidouni, S., Du, X. Evaluation the Impact of Flexible Joints and Deck on the Seismic Response of Bridges. Computational Engineering and Physical Modeling, 2022; 5(2): 1-18. https://doi.org/10.22115/cepm.2022.321993.1198
Haque, A., Saha, O., Aziz, M. Flood Hazard Mapping of the Floodplain of the Jamuna River. Computational Engineering and Physical Modeling, 2022; 5(1): 89-101. https://doi.org/10.22115/cepm.2022.327103.1201
Babaei, M., Moradi, M. Multi-objective Optimization of Steel Frames with Added Viscous Dampers using Imperialist Competitive Algorithm. Computational Engineering and Physical Modeling, 2022; 5(1): 69-88. https://doi.org/10.22115/cepm.2022.345345.1212
Asif, T., Islam, S., Basak, A., Shahriar, F., Rahman, S. Application of Numerical Method in Assessing the Variations in Pile Group Efficiency under Different Circumstances. Computational Engineering and Physical Modeling, 2022; 5(1): 50-68. https://doi.org/10.22115/cepm.2022.324662.1200
Zaki, R., Risan, H. Systematic Review for Behavior of Post-Tensioned Concrete Members with Different Tendon Bonding Conditions. Computational Engineering and Physical Modeling, 2022; 5(1): 36-49. https://doi.org/10.22115/cepm.2022.309587.1186
Gupta, V., Reddy, G., Pendhari, S. Performance-Based Design of RC Structures Subjected to Seismic Load Using a Hybrid Retrofitting Method with Friction Damper and Steel Bracing. Computational Engineering and Physical Modeling, 2022; 5(1): 19-35. https://doi.org/10.22115/cepm.2022.317119.1191
Salehi Fereidouni, S., Du, X. Investigation on the Seismic Performance of Joints with Different Shapes in Bridge Columns. Computational Engineering and Physical Modeling, 2022; 5(1): 1-18. https://doi.org/10.22115/cepm.2022.321707.1197
Ye, Y., Fu, C., Huang, X. Vehicle Bridge Interaction Analysis on Concrete and Steel Curved Bridges. Computational Engineering and Physical Modeling, 2021; 4(4): 94-108. https://doi.org/10.22115/cepm.2021.272934.1155
Ekwule, O., Ugbede, M., Akpen, D. The Effect of Heavy Metal Concentration on the Soil of Odagbo Area, Kogi State Nigeria. Computational Engineering and Physical Modeling, 2021; 4(4): 84-93. https://doi.org/10.22115/cepm.2021.292378.1177
Verma, V., Malloth, A., Nallasivam, K. Modal Analysis of a Thin-Walled Box-Girder Bridge and Railway Track Using Finite Element Framework. Computational Engineering and Physical Modeling, 2021; 4(4): 68-83. https://doi.org/10.22115/cepm.2021.278798.1165
Ferdowsi, A., Nemati, M., Farzin, S. Development of Dam-Break Model Considering Real Case Studies with Asymmetric Reservoirs. Computational Engineering and Physical Modeling, 2021; 4(4): 39-63. https://doi.org/10.22115/cepm.2021.311759.1188
Roy, A., Sardalia, A., Singh, J. Wind Induced Pressure Variation on High-Rise Geometrically Modified Building Having Interference through CFD Simulation. Computational Engineering and Physical Modeling, 2021; 4(4): 26-38. https://doi.org/10.22115/cepm.2021.271960.1151
Khademi, A., Behfarnia, K., Kalman Šipoš, T., Miličević, I. The Use of Machine Learning Models in Estimating the Compressive Strength of Recycled Brick Aggregate Concrete. Computational Engineering and Physical Modeling, 2021; 4(4): 1-25. https://doi.org/10.22115/cepm.2021.297016.1181
Kulkarni, S., Pendhari, S. 3D Semi-Analytical Solutions for Functionally Grade Power Law Varied Laminate Subjected to Thermo-Mechanical Loading. Computational Engineering and Physical Modeling, 2021; 4(3): 70-98. https://doi.org/10.22115/cepm.2021.265578.1148
Rahman, I., Shahriar, M., Rahman, S. Numerical Analysis of Flow and Heat Transfer Characteristics between Two Parallel Plates with Constriction(s). Computational Engineering and Physical Modeling, 2021; 4(3): 55-69. https://doi.org/10.22115/cepm.2021.281818.1167
Cimagala, J. Optimization of Reduced Beam Sections (RBS) for Ductile Detailing of Seismic Joint Connections Using Finite Element Analysis (FEA). Computational Engineering and Physical Modeling, 2021; 4(3): 43-54. https://doi.org/10.22115/cepm.2021.273581.1153
Gupta, S., Islam, T., Sohag, M., Salakin, S., Hossain, I. Experimental Study of Concrete Using Raw Rice Husk as Partial Replacement of Cement with Natural Fiber (Jute Fiber) as Reinforcing Material. Computational Engineering and Physical Modeling, 2021; 4(3): 29-42. https://doi.org/10.22115/cepm.2021.280252.1166
Martins, J., Janghu, R., Romão, E. Numerical Simulation of Stresses Produced on Hydraulic Clutch Discs due to Heat Generated During Operation. Computational Engineering and Physical Modeling, 2021; 4(3): 19-28. https://doi.org/10.22115/cepm.2021.277513.1164
Kumar, B., Kumar, G., Rajesh, V. Development of Fly ash-GGBS based Self Compacting Geo-Polymer Concrete with and without Steel Fibres. Computational Engineering and Physical Modeling, 2021; 4(3): 1-18. https://doi.org/10.22115/cepm.2021.276291.1163
Kotnurkar, A., Talawar, V. Influence of Jeffrey Nanofluid on Peristaltic Motion in an Inclined Endoscope. Computational Engineering and Physical Modeling, 2021; 4(2): 68-94. https://doi.org/10.22115/cepm.2021.261607.1142
Islam, S., Mominul Alam, S., Akter, S. Identifying the Amount of Heat Flux and Thermal Conduction through Fabrics with Appropriate Heat Equation. Computational Engineering and Physical Modeling, 2021; 4(2): 53-67. https://doi.org/10.22115/cepm.2021.239419.1118
Shahrokhinasab, E., Chitty, F., Vahedi, M., Zolfagharysaravi, S. Improvement of Concrete Characterization Using Nanosilica. Computational Engineering and Physical Modeling, 2021; 4(2): 39-52. https://doi.org/10.22115/cepm.2021.250011.1133
Chaid, R., Mesbah, H., Haddadou, N., Hamza, M. Contribution of the Blast Furnace Slag on the Behavior of HPC in a Hydrochloric Environment. Computational Engineering and Physical Modeling, 2021; 4(2): 27-38. https://doi.org/10.22115/cepm.2021.233313.1108
Kvocak, V., Dubecky, D., Vanova, P. Prefabricated Composite Beams Based on Innovative Shear Connection. Computational Engineering and Physical Modeling, 2021; 4(2): 20-26. https://doi.org/10.22115/cepm.2021.233573.1109
Fallahi, M., Cheraghi Seifabad, M., Baghbanan, A. Rock Slope Stability Analysis in the Left Abutment of Bakhtiary Dam, Iran. Computational Engineering and Physical Modeling, 2021; 4(2): 1-19. https://doi.org/10.22115/cepm.2021.254912.1134
Li, F., Chapuis, A., Liu, Q. Effect of Threshold Twin Volume Fraction in Crystal Plasticity Modeling. Computational Engineering and Physical Modeling, 2021; 4(1): 84-100. https://doi.org/10.22115/cepm.2021.245719.1128
Shakeri, M. The Relation between Deposited Weight and Quality of Coating in EPD Method Derived by Genetic Programming. Computational Engineering and Physical Modeling, 2021; 4(1): 73-83. https://doi.org/10.22115/cepm.2020.239389.1117
Azunna, S., Ogar, J. Characteristic Properties of Concrete with Recycled Burnt Bricks as Coarse Aggregates Replacement. Computational Engineering and Physical Modeling, 2021; 4(1): 56-72. https://doi.org/10.22115/cepm.2021.245270.1126
Mohamed, M., El-Sayed, A., Megalla, K., Elattar, H. Cost Analysis of a Large Solar Plant with Parabolic Trough Concentrators Using Molten Salt Storage Tank. Computational Engineering and Physical Modeling, 2021; 4(1): 37-55. https://doi.org/10.22115/cepm.2021.240381.1120
Abdolrezayi, A., Khayat, N. Comparative Three-Dimensional Finite Element Analysis of Piled Raft Foundations. Computational Engineering and Physical Modeling, 2021; 4(1): 19-36. https://doi.org/10.22115/cepm.2020.234834.1111
Granitzer, A., Tschuchnigg, F. Numerical Analysis of Segmental Tunnel Linings employing a Hybrid Modeling Approach. Computational Engineering and Physical Modeling, 2021; 4(1): 1-18. https://doi.org/10.22115/cepm.2021.247314.1130
Azunna, S., Nwafor, E., Ojobo, S. Stabilization of Ikpayongu laterite using Cement, RHA and Carbide Waste Mixture for Road Subbase and Base Material. Computational Engineering and Physical Modeling, 2020; 3(4): 77-96. https://doi.org/10.22115/cepm.2020.238161.1114
Tusher, H., Hasnat, A., Rahman, F. A Circumstantial Review on Ride-sharing Profile in Dhaka City. Computational Engineering and Physical Modeling, 2020; 3(4): 58-76. https://doi.org/10.22115/cepm.2020.236247.1112
Shabani, M., Habibi, S., Kalani, L. Numerical Analysis of Reverse Dip-slip Fault Rupture on Steel Buildings. Computational Engineering and Physical Modeling, 2020; 3(4): 40-57. https://doi.org/10.22115/cepm.2020.225647.1097
Kulkarni, S., Pendhari, S. Cylindrical Bending of Power Law Varied Functionally Graded Laminate Subjected to Thermo-Mechanical Loading. Computational Engineering and Physical Modeling, 2020; 3(4): 20-39. https://doi.org/10.22115/cepm.2020.243741.1124
Asaeian, A., Abedi, M., Jafari-Talookolaei, R., Attar, M. Wave Propagation through a Submerged Horizontal Plate at the Bottom of a Water Channel. Computational Engineering and Physical Modeling, 2020; 3(4): 1-19. https://doi.org/10.22115/cepm.2020.243377.1123
Ojo, O., Olaleke, O., Dahunsi, O. Design, Fabrication and Structural Analysis of a 5 Tons Hydraulic Press and Mould Machine for Crucible Production. Computational Engineering and Physical Modeling, 2020; 3(3): 46-58. https://doi.org/10.22115/cepm.2020.237362.1113
Salajeghe, A., Kamgar, R., Rahgozar, R. Improving the Behavior of Non-Uniform Tall Structures in Determining the Optimum Location of Belt Truss System. Computational Engineering and Physical Modeling, 2020; 3(3): 34-45. https://doi.org/10.22115/cepm.2020.230337.1107
Vhanmane, M., Bhanuse, M. Analysis of Diagrid Structural System for High Rise Steel Buildings. Computational Engineering and Physical Modeling, 2020; 3(3): 21-33. https://doi.org/10.22115/cepm.2020.223505.1092
Asadi, A., Saba, H. Evaluation of the Effect of Modulus of Elasticity in Clay Core on the Arching in the Crest of Earth Dams. Computational Engineering and Physical Modeling, 2020; 3(3): 12-20. https://doi.org/10.22115/cepm.2020.225075.1096
Romero, R., Romero, N., Romero, F., Cronico, J. Assessing Flood Occurrence and Modeling Impact of Urban Drainage Structure. Computational Engineering and Physical Modeling, 2020; 3(3): 1-11. https://doi.org/10.22115/cepm.2020.221035.1090
Alizadeh, S., Frohid, A. A Field Study of the Impact of Human Characteristics on the Use of Signs. Computational Engineering and Physical Modeling, 2020; 3(2): 51-62. https://doi.org/10.22115/cepm.2020.217012.1083
Morsali, S., Yücel Işildar, G. Determination of Environmental Impacts of Bituminous Highway’s by Life Cycle Assessment. Computational Engineering and Physical Modeling, 2020; 3(2): 38-50. https://doi.org/10.22115/cepm.2020.209139.1074
Asadi, A., Saba, H. Comparative Study of a Subgrade Coefficient Reaction on an Arched Dam Using the Winkler Foundation Model. Computational Engineering and Physical Modeling, 2020; 3(2): 29-37. https://doi.org/10.22115/cepm.2020.223676.1094
Ogbonna, C., Mbadike, E., Alaneme, G. Characterisation and Use of Cassava Peel Ash in Concrete Production. Computational Engineering and Physical Modeling, 2020; 3(2): 12-28. https://doi.org/10.22115/cepm.2020.223035.1091
Patil, A., Bhanuse, M. Seismic Analysis of Eccentric Steel Structure on a Shaking Table. Computational Engineering and Physical Modeling, 2020; 3(2): 1-11. https://doi.org/10.22115/cepm.2020.223528.1093
Pirmohammadi Alishah, F. The Effect of Zeolite on Different Mechanical Properties and Permeability of Self-Compacting Concrete. Computational Engineering and Physical Modeling, 2020; 3(1): 53-68. https://doi.org/10.22115/cepm.2020.214817.1079
Alaneme, G., Mbadike, E. Modelling of the Compressive Strength of Palm-Nut-Fibre Concrete Using Scheffe’s Theory. Computational Engineering and Physical Modeling, 2020; 3(1): 36-52. https://doi.org/10.22115/cepm.2020.212999.1076
Ghasemi, M., Roshani, G., Roshani, A. Detecting Human Behavioral Pattern in Rock, Paper, Scissors Game Using Artificial Intelligence. Computational Engineering and Physical Modeling, 2020; 3(1): 25-35. https://doi.org/10.22115/cepm.2020.215668.1081
Keerthi Gowda, B., Dakshayini, M. Application of FOSM and Chebyshev’s Theorem Concept to Predict Compressive Strength Attributes of Corncob Ash Embedded Cement Concrete. Computational Engineering and Physical Modeling, 2020; 3(1): 16-24. https://doi.org/10.22115/cepm.2020.212079.1075
Bodda, S., Gupta, A., Ju, B., Jung, W. Fragility of a Weir Structure due to Scouring. Computational Engineering and Physical Modeling, 2020; 3(1): 1-15. https://doi.org/10.22115/cepm.2020.214539.1077
Kiran, K., Kori, J. Blast Mitigations of Mid Rise Structures by Cladding Material. Computational Engineering and Physical Modeling, 2019; 2(4): 78-94. https://doi.org/10.22115/cepm.2020.196935.1066
Akano, T., Olayiwola, P. Numerical Investigation into the Effect of Laminated Casing on the Impact Resistance of Smartphone Screens. Computational Engineering and Physical Modeling, 2019; 2(4): 58-77. https://doi.org/10.22115/cepm.2020.184606.1063
Hassan, S., Himika, T., Molla, M., hasan, F. Lattice Boltzmann Simulation of Fluid Flow and Heat Transfer through Partially Filled Porous Media. Computational Engineering and Physical Modeling, 2019; 2(4): 38-57. https://doi.org/10.22115/cepm.2020.200817.1070
Ibitolu, B., Jimoh, A., Babatunde, O. EN 338 Strength Characterization and Grading of Igba (Rhizophora Racemosa) and Adere (Syzgium Guineense) Timbers for Structural Applications. Computational Engineering and Physical Modeling, 2019; 2(4): 24-37. https://doi.org/10.22115/cepm.2020.159153.1051
Makarios, T., Bakalis, A. New Seismic Pushover Procedures using either Floor Enforced-Displacements or Inelastic Dynamic Eccentricities on Irregular Single-Storey R/C Buildings. Computational Engineering and Physical Modeling, 2019; 2(4): 1-23. https://doi.org/10.22115/cepm.2020.216973.1082
Jabbari, M., Behzadi, S. Modelling Effects of Land Use Changes on Traffic Based on Proposed Traffic Simulator. Computational Engineering and Physical Modeling, 2019; 2(3): 53-64. https://doi.org/10.22115/cepm.2020.207903.1073
Mota Silva, J., Bastos, L., Santos da Silva, J. Human Comfort Assessment of Buildings Considering the Effect of the Masonry Infills and the Soil-Structure Interaction. Computational Engineering and Physical Modeling, 2019; 2(3): 38-52. https://doi.org/10.22115/cepm.2020.205633.1071
Taiwo, A., Ndububa, E., Olarewaju, K. Chemical Composition of Commonly Used Local and Foreign Steel Reinforcements and the Effects on the Strength Property of the Material Composites. Computational Engineering and Physical Modeling, 2019; 2(3): 27-37. https://doi.org/10.22115/cepm.2019.168122.1057
Alqarni, M., Noman, A., Bashir, M. Numerical Simulation and Parametric Study on the Moment Capacity of Composite Beam. Computational Engineering and Physical Modeling, 2019; 2(3): 16-26. https://doi.org/10.22115/cepm.2019.199497.1069
Bagherzadeh Khalkhali, A., Kabiri Koochaksaraei, M. Evaluation of Limit Equilibrium and Finite Element Methods in Slope Stability Analysis - Case Study of Zaremroud Landslide, Iran. Computational Engineering and Physical Modeling, 2019; 2(3): 1-15. https://doi.org/10.22115/cepm.2019.206590.1072
Kiyani, K., Raeisi, J., Heidari, A. Time-Frequency Localization of Earthquake Record by Continuous Wavelet Transforms. Computational Engineering and Physical Modeling, 2019; 2(2): 49-61. https://doi.org/10.22115/cepm.2019.193015.1065
Siddika, A., Awall, M., Mamun, M., Humyra, T. Study on Natural Frequency of Frame Structures. Computational Engineering and Physical Modeling, 2019; 2(2): 36-48. https://doi.org/10.22115/cepm.2019.183201.1062
Abdullahi Alao, J. Design Formula at Ultimate Stresses for Ekki (Lophira Alata) Timber Beam. Computational Engineering and Physical Modeling, 2019; 2(2): 25-35. https://doi.org/10.22115/cepm.2019.159164.1053
Houari, O. Using Pressuremeter Test Results to Estimate Bearing Capacity in the Vicinity of a Slope- Numerical Analysis-. Computational Engineering and Physical Modeling, 2019; 2(2): 15-24. https://doi.org/10.22115/cepm.2019.186146.1064
Eliseev, A., Mironov, A., Eliseev, S. Approaches in the Development of Motion Sensors in the Dynamics of Granular Media. Computational Engineering and Physical Modeling, 2019; 2(2): 1-14. https://doi.org/10.22115/cepm.2019.127447.1025
Adeke, P., Joel, M., Edeh, J. Simulation of Priority Queuing at TOTAL Petrol Filling Station in Makurdi Town Using SimEvents Toolkit. Computational Engineering and Physical Modeling, 2019; 2(1): 56-66. https://doi.org/10.22115/cepm.2019.171928.1060
Bakhshi, H., Khosravi, H., Ghoddusi, M. Evaluation of Seismic Behavior of Steel Shear Wall by Time History Analysis. Computational Engineering and Physical Modeling, 2019; 2(1): 38-55. https://doi.org/10.22115/cepm.2019.160278.1055
Baiat Ghiasi, S., Oyar Hossein, M., Adineh, M., Khiali, V. Investigating on Hydrodynamic Behavior of Slotted Breakwater Walls Under Sea Waves. Computational Engineering and Physical Modeling, 2019; 2(1): 30-37. https://doi.org/10.22115/cepm.2019.172568.1059
Taiwo, A., Ayinde, R. Comparative Studies of the Effects of Blocking and Water Repellant Agents on Tensile Strengths of Fanpalm. Computational Engineering and Physical Modeling, 2019; 2(1): 17-29. https://doi.org/10.22115/cepm.2019.146916.1045
Singh, J., Roy, A. Wind Pressure Coefficients on Pyramidal Roof of Square Plan Low Rise Double Storey Building. Computational Engineering and Physical Modeling, 2019; 2(1): 1-16. https://doi.org/10.22115/cepm.2019.144599.1043
Chabokan, E., Faridmehr, I. Seismic Assessment of Steel Moment Frames with Irregularity in Mass and Stiffness. Computational Engineering and Physical Modeling, 2018; 1(4): 71-89. https://doi.org/10.22115/cepm.2018.141604.1039
Odeyemi, S., Adedeji, A. Modelling and Simulation of Reinforced Concrete Bridges with varying percentages of Shape Memory Alloy Rods. Computational Engineering and Physical Modeling, 2018; 1(4): 62-70. https://doi.org/10.22115/cepm.2018.141829.1040
Ameur, H., Kamla, Y., Sahel, D. Numerical Investigation of the Cooling of Shear Thinning Fluids in Cylindrical Horizontal Ducts. Computational Engineering and Physical Modeling, 2018; 1(4): 53-61. https://doi.org/10.22115/cepm.2018.148483.1047
Ankidawa, B., Ishaku, J., Hassan, A. Estimation of Aquifer Transmissivity Using Dar Zarrouk Parameters Derived from Resistivity Soundings on the Floodplain of River Dadin Kowa, Gombe State, Northeastern Nigeria. Computational Engineering and Physical Modeling, 2018; 1(4): 36-52. https://doi.org/10.22115/cepm.2018.129584.1024
Salama, M. Elastic Buckling of Single-Stepped Columns with End and Intermediate Axial Loads. Computational Engineering and Physical Modeling, 2018; 1(4): 25-35. https://doi.org/10.22115/cepm.2018.147218.1046
Naderpour, H., Mirrashid, M. A Computational Model for Estimating the Compressive Strength of Mortars Admixed with Mineral Materials. Computational Engineering and Physical Modeling, 2018; 1(4): 16-24. https://doi.org/10.22115/cepm.2018.136069.1031
Sobamowo, G., Jayesimi, O., Waheed, A. On the Study of Magnetohydrodynamic Squeezing Flow of Nanofluid between Two Parallel Plates Embedded in a Porous Medium. Computational Engineering and Physical Modeling, 1999; 1(4): 1-15. https://doi.org/10.22115/cepm.2018.122325.1013
Azimi, A., Farahnaki, R. Flexural Capacity Prediction for Reinforced Concrete Beams by Group Method of Data Handling Approach. Computational Engineering and Physical Modeling, 2018; 1(3): 100-110. https://doi.org/10.22115/cepm.2018.136502.1033
Kiran, K., Kori, J. Controlling Blast Loading of the Structural System by Cladding Material. Computational Engineering and Physical Modeling, 2018; 1(3): 79-99. https://doi.org/10.22115/cepm.2018.141294.1038
Ahani, A., Ahani, E., Abbaszadeh, H. The Effects of Outrigger Type and Distribution on Seismic Behavior of Super-Tall Building. Computational Engineering and Physical Modeling, 2018; 1(3): 67-78. https://doi.org/10.22115/cepm.2018.125321.1016
Wang, L., Wang, P. Modeling of the New Boundary of Reaction Force Based on Particle Collision in the Smoothed Particle Hydrodynamics. Computational Engineering and Physical Modeling, 2018; 1(3): 46-66. https://doi.org/10.22115/cepm.2018.141232.1037
Chawhan, B., Quadri, S. Experimental and Numerical Investigations of Laterally Loaded Pile Group in Multilayered Cohesionless Soil. Computational Engineering and Physical Modeling, 2018; 1(3): 28-45. https://doi.org/10.22115/cepm.2018.108513.1005
Mahdi, M., Marie, I. Three-Dimensional Modelling of Concrete Mix Structure for Numerical Stiffness Determination. Computational Engineering and Physical Modeling, 2018; 1(3): 15-27. https://doi.org/10.22115/cepm.2018.118218.1010
Kashefizadeh, M., Azimzadeh Koocheh, M., Amiri, B., Esmaeilabadi, R. Steel Plate Shear Wall with Different Infill Steel Plates. Computational Engineering and Physical Modeling, 2018; 1(3): 1-14. https://doi.org/10.22115/cepm.2018.118244.1011
Babaei, M., Moniri, A. Use of Tuned Mass Dampers in Controlling the Vibrations of Steel Structures with Vertical Irregularity of Mass. Computational Engineering and Physical Modeling, 2018; 1(2): 83-94. https://doi.org/10.22115/cepm.2018.137303.1035
Ankidawa, B., Zakariah, D. Design and Evaluation of Drip Irrigation System for Date Palm Plantations in MAUTECH, Yola, Adamawa State, Northeastern Nigeria. Computational Engineering and Physical Modeling, 2018; 1(2): 70-82. https://doi.org/10.22115/cepm.2018.134525.1030
Salama, M. Buckling of Tapered Columns with Polygon Cross-Section. Computational Engineering and Physical Modeling, 2018; 1(2): 59-69. https://doi.org/10.22115/cepm.2018.136082.1032
Thombare, C., Sangle, K., Mohitkar, V., Kharmale, S. Efficient Configuration of Storage Rack System as Per Nonlinear Static Pushover Analysis under Triangular and Uniform Pattern of Lateral Loading Pattern. Computational Engineering and Physical Modeling, 2018; 1(2): 41-58. https://doi.org/10.22115/cepm.2018.125616.1017
Abbaszadeh, H., Ahani, A., Emami Azadi, M. Debonding and Fracture Behavior of Concrete Specimens Retrofitted by FRP Composite. Computational Engineering and Physical Modeling, 2018; 1(2): 27-40. https://doi.org/10.22115/cepm.2018.125309.1015
Funari, M., Lonetti, P., Pascuzzo, A. A Moving Cohesive Mesh Formulation to Predict Debonding Phenomena in Layered Structures. Computational Engineering and Physical Modeling, 2018; 1(2): 16-26. https://doi.org/10.22115/cepm.2018.132122.1028
Sobamowo, G., Yinusa, A. Transient Combustion Analysis for Iron Micro-Particles in a Gaseous Oxidizing Medium Using Adomian Decomposition Method. Computational Engineering and Physical Modeling, 2018; 1(2): 1-15. https://doi.org/10.22115/cepm.2018.122052.1012
Jandaghian, Z. Flow and Pollutant Dispersion Model in a 2D Urban Street Canyons Using Computational Fluid Dynamics. Computational Engineering and Physical Modeling, 2018; 1(1): 83-93. https://doi.org/10.22115/cepm.2018.122506.1014
Bunyamin, S., Aghayan, S. Settlement Modelling of Raft Footing Founded on Oferekpe/Abakaliki Shale in South East Region of Nigeria. Computational Engineering and Physical Modeling, 2018; 1(1): 68-82. https://doi.org/10.22115/cepm.2018.116754.1009
Amiri, B., AghaRezaei, H., Esmaeilabadi, R. The Effect of Diagonal Stiffeners on the Behaviour of Stiffened Steel Plate Shear Wall. Computational Engineering and Physical Modeling, 2018; 1(1): 58-67. https://doi.org/10.22115/cepm.2018.112951.1007
Azadi Kakavand, M., Khanmohammadi, M. Seismic Fragility Assessment of Local and Global Failures in Low-rise Non-ductile Existing RC Buildings: Empirical Shear-Axial Modelling vs. ASCE/SEI 41 Approach. Computational Engineering and Physical Modeling, 2018; 1(1): 38-57. https://doi.org/10.22115/cepm.2018.114549.1008
Jimoh, A., Rahmon, R., Ajide, S. Reliability-Based Investigation on Compressive Strength Characteristics of Structural-Sized Iroko (Meliceae Excelsa) and Mahogany (Khaya Ivorensis) Timber Column Found in Nigeria. Computational Engineering and Physical Modeling, 2018; 1(1): 23-37. https://doi.org/10.22115/cepm.2018.105453.1002
Mahdi, M., Marie, I. Numerical Simulation of Concrete Mix Structure and Detection of its Elastic Stiffness. Computational Engineering and Physical Modeling, 2018; 1(1): 12-22. https://doi.org/10.22115/cepm.2018.54011
Torkian, H., Keshavarz, Z. Determining the Drift in Reinforced Concrete Building Using ANFIS Soft Computing Modeling. Computational Engineering and Physical Modeling, 2018; 1(1): 1-11. https://doi.org/10.22115/cepm.2018.53677